• Applicable for:  E22158 SeaTalk one to SeaTalkng converter
  • Software Version: v2.03
  • Release Date: September 2016
 

Downloading the Software


Select the software update below depending on which Multifunction Display you will be using to perform the Remote Update. Please note if you have a G Series or a/c/e/gS Series you must check what version of software you have installed in the unit that you are using to perform the upgrade. For further information on this please click here.


Current MFDs

 

AXIOM/AXIOM Pro

AXIOM 7 184x169Download  

eS Series

eS SeriesDownload  

a/c/e/gS Series

a/c/e/gS Series Software | Raymarine by FLIRDownload  
 

Retired / Legacy MFDs

 

G Series

G SeriesDownload  

E Wide

E WideDownload  

C Wide

C WideDownload  

E Classic

E ClassicDownload  

C Classic

C ClassicUnavailable  

A Classic

A ClassicDownload  
Important Notes

  • With the introduction of version 1.10, the converter now supports a system with a Autopilot.  With version 1.11 you are now able to connect and communicate with a previous generation of Autopilot such as the S1G, S2G and S3G as examples.  Information in the manual regarding not being able to connect the converter with a Autopilot in the system is now redundant.
     
 


View Update Instructions |  View Latest Manual


 

IMPORTANT TERMS OF DOWNLOADING SOFTWARE

 

This firmware update process is done at your own risk. Before initiating the update process be sure to backup and make copies of all important files. 

If the firmware process is interrupted your product may not function properly, therefore do not interrupt the process and ensure the unit is on a reliable power supply. Damage caused by incomplete upgrades will not be covered by Raymarine warranty. 

By Downloading the software, you agree to these terms.

 

Open Source GPL/LGPL

Some Raymarine products contain software code developed by third parties that are covered by open source GPL and LGPL software license agreements. You can view the third party license agreements by visiting the Manuals and Documents section of our website.

To access the open source GPL and LGPL licensed executables click here

 


Software History


Version Release Date Features
v2.03 Sept 2016
  • STng converter now correctly decodes Rudder information when bridging from STng onto SeaTalk1.
    • The symptom of this issue was typically seen on the Smart Controller once R4 software was loaded into the EVO pilots, whereby the rudder bar/angle would either show as Hard Over, or would jump about.
v2.01 Oct 2015
  • Converter does not Block MDS Selection Feature when operating in NMEA0183 mode
v2.00 Oct 2015
  • Support for Multiple Data Selection (MDS) feature
    • Converter no longer blocks the MDS feature
    • Data such as Speed, Depth, Wind, Heading & GPS bridged from SeaTalk1 to SeaTalkng can be selected as the system data source.
  • Support for Global Selection of Units
    •  The converter will now support and retain the system units selection from an i70 or MFD, throughout a powercycle.
  • General SeaTalkng data improvements
v1.21 March 2013
  • NMEA0183 OUTPUT mode for connection to an isolated NMEA0183 VHF data input
  • Variation / heading conversion issue fixed
  • Units conversion improvement
v1.14 March 2012
  • Improved support for support for the Seatalk 1 Joystick
v1.11 Sept 2011
  • Improved tunneling of Autopilot messages -corrects the intermittent error message of “nopilot” being displayed on SeaTalk1 control units, when being tunneled through the STNG backbone.
v1.10 April 2011
  • Autopilot tunnelled messages now supported.  
  • Speed-through-the-Water (STW) Invalidity Check implemented, to ensure Converter doesn’t stop the conversion of STW from other sources.
  • Converter now automatically checks / upgrades its boot loader at power on.
  • PGN 129540 modified to transmit correct status value for satellites used in Differential mode.
  • PGN 129029 now correctly initializes the default values for PDOP, Geoidal Separation, Altitude and Integrity, to “unavailable”.
  • Default starting source address preset to 115 instead of 0, to resolve some PGN conflicts from other sources
 
v1.01 Sept 2010
  • Corrects an intermittent error in SOG data, when the converter is being used to convert the RS125+ from Seatalk1 to SeatalkNG.
 
v1.00 July 2010
  • Initial Release